Ganador Super Mirror Pegs: Fitment and Replacement FAQ

Quick answer

Ganador Super Mirror replacement pegs are the small fittings that join the mirror glass backing plate to the adjuster or motor assembly inside the housing. If a peg is cracked, missing, or no longer holds, the glass can wobble or fail to aim correctly. Replace the pegs as a set, and confirm your mirror uses Ganador Super Mirror backing plates before ordering.

What the pegs actually do inside a Ganador Super Mirror

The pegs sit between the glass backing plate and the adjuster or motor. They are what let the mirror move and hold an angle instead of sitting loose in the housing. When one peg is damaged, the glass can tilt unevenly or refuse to stay where you set it, even if the motor still runs.

• A missing peg usually shows up as a mirror that flops or drifts at speed.
• A cracked peg can make adjustment feel notchy or inconsistent.
• A peg that no longer seats can cause the glass to sit proud of the housing.

When to replace Ganador mirror pegs instead of the whole mirror

Replacement pegs make sense when the housing, motor, and glass are still serviceable and the only failure is in the peg or backing-plate interface. If the mirror glass is shattered, the housing is cracked, or the adjuster no longer moves at all, pegs alone will not fix the problem. Inspect the backing plate for cracks before ordering, because a damaged plate can prevent new pegs from seating correctly.

• Replace pegs when adjustment is loose but the motor still responds.
• Replace the mirror assembly when the housing or glass is broken.
• If the backing plate is cracked, address that before installing new pegs.

How to check Ganador mirror fitment before you buy

Fitment comes down to the backing plate, not the car model alone. These pegs are made for Ganador Super Mirror backing plates, so confirm that is what you have before ordering. If you are unsure, remove the mirror glass and compare the peg location and shape against the old part. A peg that does not match the plate will not hold adjustment no matter how carefully it is installed.

• Confirm the mirror is a Ganador Super Mirror, not a generic replacement.
• Check that the backing plate accepts the peg pattern shown for this part.
• When in doubt, inspect the old peg before ordering.

Mirror peg installation: what to expect

Installation is a small-parts job, not a full mirror rebuild. Work on a clean surface, remove the mirror glass carefully, and keep track of the pegs and any clips as they come out. Seat each new peg fully into the backing plate before refitting the glass. Do not force a peg that will not seat; if it binds, stop and check orientation and plate condition rather than pushing harder.

• Work over a tray so small pegs do not disappear.
• Seat pegs by hand and check alignment before refitting glass.
• Test adjustment through the full range before reinstalling trim.

Common mistakes that lead to repeat failures

Most repeat failures come from reusing damaged backing plates, mixing old and new pegs, or overtightening during reassembly. If one peg failed, the others are likely aged too, so replacing them as a set is the more reliable path. Also check that the adjuster moves freely; a stiff or seized adjuster can stress new pegs and cause them to fail again.

• Replace all pegs at once rather than one at a time.
• Inspect and free up the adjuster before installing new pegs.
• Avoid overtightening; pegs should seat, not be crushed.

Ganador mirror peg FAQ

Will these pegs fit any Ganador mirror?

They are made for Ganador Super Mirror backing plates. Fitment depends on the backing plate, so confirm yours matches before ordering. Check the plate, not just the car model.

Can I replace just one peg?

You can, but if one peg has failed the others are likely aged. Replacing the set reduces the chance of a second failure shortly after. Replace as a set for a more reliable result.

What if the mirror still will not hold adjustment after new pegs?

Check the backing plate for cracks and confirm the adjuster moves freely. If either is damaged, pegs alone will not solve the problem. Inspect the plate and adjuster before blaming the pegs.

Product facts

• Ganador Super Mirror Replacement Pegs: Replacement pegs for Ganador Mirror Backing Plates; they fit into the glass backing plates and attach them to the adjusters or motors. Confirms these are the correct parts when the backing plate and adjuster are intact but the peg itself is damaged or missing.